Matek Systems BetaFlight F405


FC Specifications

  • MCU: 168MHz STM32F405
  • IMU: 32K ICM20602 accelerometer/gyro (SPI)
  • Max. 32K Gyro update & 16K PID Loop
  • OSD: BetaFlight OSD w/ AT7456E chip
  • Blackbox: MicroSD card slot (SD/SDHC)
  • VCP, UART1, UART2, UART3, UART4, UART5
  • Built in inverter for SBUS input (UART2-RX)
  • PPM/UART Shared: UART2-RX
  • SoftSerial on S5 & S6 optional
  • Smartaudio & Tramp VTX protocol supported
  • Spektrum BIND_PIN: RX4
  • WS2812 Led Strip : Yes
  • Beeper : Yes
  • RSSI: Yes

PDB Specifications

  • Input: 9~27V (3~6S LiPo) w/TVS protection
  • PDB: 4x30A (Max.4x50A), 6 layers*2oz copper PCB
  • Dual BEC: 5V 2A & 9V 2A
  • LDO 3.3V: Max.300mA for Spektrum RX
  • Current Sensor 200A (Scale 165)
  • Battery Voltage Sensor: 1:10 (Scale 110)
  • 2x LEDs for FC STATUS (Blue, Red)
  • 6x PWM / DShot outputs without conflict
  • 5x UARTs
  • 1x Group of  G/S1/S2/S3/S4 pads for 4in1 ESC Signal/GND
  • 4x pairs of corner pads for ESC Signal/GND connections (DSHOT compatible)
  • 1x pair I2C1 pads (for INAV firmware only)
  • 1x Side-press button for BOOT(DFU) mode
  • 36x51mm PCB with 30.5mm mounting holes & XT60 socket
  • 12g
  • w/ 1x Rubycon ZLH 35V/470uF (Low ESR)
  • w/ 4x M3 Anti-vibration Standoffs
  • w/ FR4 PCB Plate 36*36*1mm






$65.90

Unknown

Flight Controllers

Out of stock


FC Specifications

  • MCU: 168MHz STM32F405
  • IMU: 32K ICM20602 accelerometer/gyro (SPI)
  • Max. 32K Gyro update & 16K PID Loop
  • OSD: BetaFlight OSD w/ AT7456E chip
  • Blackbox: MicroSD card slot (SD/SDHC)
  • VCP, UART1, UART2, UART3, UART4, UART5
  • Built in inverter for SBUS input (UART2-RX)
  • PPM/UART Shared: UART2-RX
  • SoftSerial on S5 & S6 optional
  • Smartaudio & Tramp VTX protocol supported
  • Spektrum BIND_PIN: RX4
  • WS2812 Led Strip : Yes
  • Beeper : Yes
  • RSSI: Yes

PDB Specifications

  • Input: 9~27V (3~6S LiPo) w/TVS protection
  • PDB: 4x30A (Max.4x50A), 6 layers*2oz copper PCB
  • Dual BEC: 5V 2A & 9V 2A
  • LDO 3.3V: Max.300mA for Spektrum RX
  • Current Sensor 200A (Scale 165)
  • Battery Voltage Sensor: 1:10 (Scale 110)
  • 2x LEDs for FC STATUS (Blue, Red)
  • 6x PWM / DShot outputs without conflict
  • 5x UARTs
  • 1x Group of  G/S1/S2/S3/S4 pads for 4in1 ESC Signal/GND
  • 4x pairs of corner pads for ESC Signal/GND connections (DSHOT compatible)
  • 1x pair I2C1 pads (for INAV firmware only)
  • 1x Side-press button for BOOT(DFU) mode
  • 36x51mm PCB with 30.5mm mounting holes & XT60 socket
  • 12g
  • w/ 1x Rubycon ZLH 35V/470uF (Low ESR)
  • w/ 4x M3 Anti-vibration Standoffs
  • w/ FR4 PCB Plate 36*36*1mm





Related Products